Frequently Asked Questions

Most Frequently Asked Questions on "SCRAMBLERS".

1. How does the Radar Scrambler work?

A: It works on all police radar bands (x, k, ka, super wide). Inside the scrambler are 3 parts:
1) A FM chirp generator
2) A mixer diode
3) A dual ridge wave guide antenna
When the scrambler is hit by a signal, it will take the signal, and run it through the mixer, add the FM chirp to mix up the signal, and (using the antenna) reflects back this signal to the radar gun. What happens next? => The radar gun’s computer can’t recognize all the speeds; it gets confused and won’t display a reading on the gun (leaving a blank screen).
All NEW (2009 & later) scramblers work similar to above but use Pseudo Random Digital Noise (PRDN) instead of FM chirp. The radar scrambling circuit mixes Pseudo Random Digital Noise (PRDN) with the incoming police radar signal and reflects it back to the radar source so it displays no speed.

2. How does the Laser Scrambler work? This is for all "C" models, DLS and KAT with laser scrambling.

A: The laser scrambling circuit transmits a series of pulses at the same wavelength used by the police laser guns (Lidar), which are electronically timed at about 100 feet apart. When the pulses pass through the windshield they will lose up to 50% of their power. The power output is 6 to 10 times that needed to trigger the detector in the laser gun. Lidar sends out laser pulses and measures how long it takes to hit your car and come back. From the speed of light it can determine your range. It sends out several more pulses and calculates your speed from the change in distance over time. The Rocky Mountain Radar scramblers only allow the Lidar to see up to 100 feet so it is unable to calculate your speed.

3. Is the radar/laser scrambler in all of the units active or passive?

The radar scrambler is passive and the laser scrambler is active.

4. Will my unit protect me from VASCAR (airplanes and helicopters)?

No, VASCAR is basically a fancy stopwatch used to time a vehicle from point A to point B. The time between points determines your speed. It is not radar or laser there is nothing for our units to detect.

5. What is the punch-through zone?

A: The signal reflected by the unit gets stronger the closer the target is to the radar gun. The scrambler uses the radar signal as a carrier and reflects it through a high-gain antenna. It will work only as long as the scrambling signal is greater than the signal from the target. Punch-through is when these signals are equal or within 50-200 feet. There is no punch-through with laser.

6. What is the range of the laser and radar scrambler?

A: In all units the radar/laser scrambler will only scramble in the direction they are facing. They provide coverage for the entire front of your vehicle, up to (4) times the range of a radar/laser gun.

7. What is the difference between the Phazer 3, Phazer II (RMR-S201), RMR-S202, RS202D and the combination units RMR-C435, and RMR-C475?

The PHZII, PHZ3, RS202 and RS202D are strictly radar and laser scramblers. We recommend using them with any radar detector. While the combo units C435, and C475 incorporate the radar/laser scrambling capabilities with a high performance radar/laser detector.

8. Is the Phazer 3 and RMR-S201 (Phazer II) a detector?

A: NO, it will NOT alert you to any police radar. It is not designed to provide detection. It will not alert you when it is scrambling. We recommend the use of a radar detector in conjunction with the scramblers.

9. Will the scrambler Phazer 3 and RMR-S201 (Phazer II) interfere with my detector?

No, since the scramblers do not transmit a signal of its own, they will not interfere with detectors.

10. Do the units have memory?

Yes, your unit will remember the last setting even if powered off or unplugged.

11. Do the combo units C435, and C475 unit come with the scrambler activated?

A: No. The combo units ship with the scrambler de-activated. The end customer must activate the scrambler.

12. How do I know that my scrambler is activated on the C430, C435, and C475?

C430, C435, - The "T" light will light up during the start up with a soft chirp sound. When hit by radar/laser it will not come on again.
C475 - Will display the word "SCRAMBLE" with a soft chirp. Also at the end of start up mode it will display "SCRM ON".

All these units will not alert you when scrambling. You will not see the "T" nor the word "SCRAMBLING".

13. Will the units scramble the roadside trailer signs that display your speed as you approach them?

A: The roadside trailer signs use radar to determine your speed. However, they do not have a sampling computer like the Police radar guns do. These signs merely take an average and will ignore any extra signals they receive. Citations cannot be issued from these signs for this reason.

14. Will the scrambler work on photo radar?

YES, if they scramble speed from the front. If they measure from the rear you will need to place a scrambler in the rear.

Except: AZ does not use radar in fixed signs but use sensors in the road bed. Those are not radar.

15. How do I know the scrambler is working?

Some units have a self-test button, when you push the button down a yellow light will appear and you will hear a soft "chirping" sound. This tells you that the unit is working properly. If the unit malfunctions this test would not work properly and the power light would go off.

With other units, when you turn the unit on and it goes through the self-test (a series of tones), this is telling you all the circuits in the scrambler are working correctly.

16. Will the scrambler work with tinted windows?

Yes, unless the tint contains metal particles or the unit is mounted low on the dash where the windshield wipers or other metallic materials exist; this may reduce the effectiveness of the units.

17. Do the units scramble 360 degrees?

No, a scrambler is a forward scrambler. The combination units detect 360 degrees.

18. What is the range of a radar gun?

Depending on the radar gun, the range can be any where from a mile (1) to two (2) miles.

Most Frequently asked Questions on "DETECTORS"

1. What is Micro-Scan?

A: It enables our detectors to scan 2-4 times faster than any competitor’s detector, which gives you a 100% probability of detecting POP Radar. This technology is unique to Rocky Mountain Radar detectors.

2. What is Smart-Scan?

A: When a signal is detected, the unit will rescan it to ensure that it is a true signal and not a false alarm. This means less false detection. This technology is unique to Rocky Mountain Radar detectors.

3. What is P.O. P. radar?

A: POP radar is a very short pulse, about 1/10 time of instant on. The POP pulse comes on and off before most detectors can scan the frequency band to detect it. This technology is unique to Rocky Mountain Radar detectors.

4. Why does the unit only detect very short ranges?

The officer may have been using instant on or P.O.P. radar

5. What do the units detect?

They detect all bands used by police, including X, K, Ka, super wide bands and all laser. Plus it covers all frequencies.

6. Do the detectors alert you to the Safety Warning Signals?

A: Yes, we detect all safety warning radar signals, including SWS & SA. We do not decode their information, because we believe that the driver should not be confused with extra information.

7. What is the detection range on the detectors?

The range is about 3 miles in highway mode, 1.5 miles in the city.

8. Why does my radar detector ( not RMR) give me a KU alert?

SatCom frequency is used by some drug stores for nation wide service and some ATM machines.

9. How does Rocky Mountain Radar's POP detection compare with other POP detectors?

Rocky Mountain Radar was the first to recognize and design for POP detection two years ago. Rocky Mountain Radar products are 87-100% effective; since we introduced POP detection to the Industry all our competitors now claim to have that ability but they fail to disclose, however, that their best POP detection is less than 50% regardless of the brand name.

10. What is Adaptive Laser Tracking?

A: Monitors the infrared ambient noise level and adjusts the detection threshold to compensate-resulting in better Laser detection with fewer false alarms. This technology is unique to Rocky Mountain Radar detectors.

11. What is Intellivoice?

A: Declares a target once with voice, then it will only signal with tones if the same band is used within 60 seconds.

12. What is K Band?

A: This is the most commonly used radar band. K Band denotes frequencies between 24.05 and 24.25 GHz.

13. What is Ka Band?

A: The newer version of police radar, Ka incorporates both “Wide-Band” and “Super Wide-Band” and operates from 33.4 to 36.0 GHz.

14. What are SWS and SA alerts?

A: SWS – Safety Warning System and SA – Safety Alert are alerts for emergency vehicles that transmit these safety signals.

15. What are the City & Highway modes for?

A: City mode filters more of the false readings. When in City Mode, the sensitivity of the radar unit is reduced so as to reduce false readings. In Highway Mode, the unit is returned to maximum sensitivity.

16. What are Digital Voice Alerts?

A: With the use of a voice chirp, alerts are spoken via a digitally recorded message.

17. What is the Dim Control for?

A: This function allows you to adjust the brightness of your detectors display.

LEGAL

1. How are these units legal?

A: The FCC regulates all consumer products that transmit or leak radio frequency into the air (Part 15 of the FCC code). Since the scrambler and the combination units do not transmit but merely act as a reflective receiver they are legal under the FCC regulations. Regarding the laser scrambler, there are no Federal laws against transmission of infra red light, so the laser - scrambling portion is legal as well. And, all the units are FCC certified (except for the S201 – Phazer II and Phazer 3).

2. Where are these units illegal?

A: The scrambler and the combination units are illegal in CO, UT, CA, NE, OK, MN, IL, TN, VA and SC and Washington, D.C. They are legal in some provinces of Canada and many foreign countries. The combination units can be used in all states except VA, D.C. if scrambler is switched off.

3. Are your detectors FCC compliant?

Yes, all of our units are compliant and certified.

4. NEW LAW IN TENNESSEE

Effective on 07/01/06 in the State of Tennessee, a new law has banned the use of scramblers. Under this new law, we can no longer re-imburse ticket fines in Tennessee. In most of our current models, there is an internal switch to de-activate the scrambler. Since Radar Roy, Craig Peterson, Carl Fors, and Tom Martino have attacked our Scramblers as not working as advertised, "8" states have passed laws banning our products..... Makes one wonder why so many states spend so much money and effort passing these laws!

5. Are the combo units RMR-C410, RMR-C430, RMR-C435, 8RDS, RS202, RS202D and the RMR-C475 really illegal to use?

Some States have passed laws that prohibit the use of scramblers; Rocky Mountain Radar has included a switch for consumers to turn the scrambling portion of their units off in those states. We ship all units with the scrambler de-activated. To activate follow the instructions in the the manual.

TROUBLESHOOTING

1. My unit will not turn on.

A: Check the following:
1) The on/off thumbwheel on the side of the unit
2) The fuse in the power cord. (To check the fuse in the power cord, unscrew the silver tip end that plugs into the cigarette lighter. If the fuse is blown, replace with a 2 amp fast burning fuse).
3) The fuse for your cigarette lighter
4) If it is none of these, return the unit to the manufacturer for repair/replace at our discretion.

2. Why does my detector give me an alert but no lights?

Check the dim position. If this is not the problem return back to manufacturer for warranty.

3. My detector has no sound.

If there is no sound detecting but only at the start up, the unit is in mute. Start up ignores any settings you have it on. No sound at all (even at setup) then you must send the unit in for warranty repair to the manufacturer.

4. Why doesn't my detector go off at electric doors/alarms?

The detector will not false alarm as much if your detector has Smart-Scan. Make sure the city button is not on.

5. Which light indicates what on the combination units?

A: On the C430 units, left to right:
1) Power – green
2) Test – amber
3) X – green
4) K – yellow
5) KA – amber
6) For laser everything across will light up

On the C435 units, left to right:
1) Power – amber
2) Test – green
3) X – red
4) K – green
5) KA – green
6) For laser everything across will light up
On the C450 units, left to right:
1) Power – amber
2) Test – green
3) X – red
4) K – green
5) KA – green
6) For laser everything across will light up.
On the C475 units the display is menu driven and will read off the settings.

6. My unit worked fine & now it does not go off?

Make sure you have not put the unit in the mute mode. The unit will stay in mute even if you turn the unit off and back on again. The unit has memory, whatever function you place it in will remain until you change it. Another way of checking if it is on mute is to see if you see the display showing it is detecting but you hear no sound.

7. How do I change the tone on the units with selectable tone?

Hold down the mute button for 3 seconds this will change the tone.

On the C475 select the tone using the menu button. Press and hold the menu button for 5 seconds to go into menu mode. When menu is displayed press and release in step increments until the high or low tone is displayed use the select button to select desired tone.

8. How much does it cost to fix my unit?

Out of warranty fees are:

All D, DLS models and KAT models are $25.00
All scrambler only models are $37.00
All combo units are $62.00

9. My unit is speaking Spanish how do I change the language back to English?

On the C475 select the tone using the menu button. Press and hold the menu button for 5 seconds to go into menu mode. When menu is displayed press and release in step increments until the English voice/Spanish voice is displayed then use the select button to select desired language.

All other models press and hold the Dim button and power up the unit.

10. How do I change the tone on the units with selectable tone?

A: Hold down the mute button for 3 seconds this will change the tone.
On the C475 select the tone using the menu button. Press and hold the menu button for 5 seconds to go into menu mode. When menu is displayed press and release in step increments until the high or low tone is displayed use the select button to select desired tone.

Most Frequent Asked Questions on "VG-2/VG-3".

1. What is VG-2/VG-3?

VG-2 is a device police use to detect the leakage from a detector. It is used in states where detectors are banned, and for commercial vehicles. VG-3 is a new unit designed to detect high end detectors.

2. What does VG-2 enable?

The DLS310 is VG-2 & VG-3 undetectable. If you are not in a state where detectors are legal or not in a commercial vehicle you should deactivate the VG-2 function to speed up radar detection. When VG-2 is activated, the DLS310 will alert you to an officer using a detector - detector (VG-2) in the area.

3. Does my unit cover VG-2 & VG-3?

Yes, but you have to activate that function to detect them. The units are not detectable by VG-2/VG-3.

4. Do the detectors come with the VG-2 on?

On Combo units the VG-2 is de-activated. D, DLS and Kat product comes VG-2 activated.

5. Is my unit detectable?

No, they are not detectable by VG-2 & VG-3. Caution must be used, however, where detectors are not allowed so they are not visually seen.

6. How do I know that my VG-2 is activated on the C430, C435, and C475?

When you turn on the unit at the end of the start up the power light will flash. This lets you know that the VG-2 detection is activated. On the C475 the VG2 status will display on the screen.

7. Does enabling vg-2 slow down the radar detection or scrambler? Does it affect the radar/laser scrambler?

Yes it slows down detection. VG-2 sweeps just like a detector, so to detect we must stop and wait for it to complete its sweep. The amount of time is short - about 1/8th second. While we are waiting, we are not looking for radar. With VG-2 off, we skip this cycle completely and continuously look for radar. It does not affect laser detection as we do this in parallel. There is no affect at all on scrambling.

INSTALLATION ON WINDOW MOUNTED UNITS

1. Where is the best place to mount my unit?

The manufacturer recommends mounting your unit in the center of the windshield (right below the rear-view mirror) for maximum coverage. There must be no metallic interference with the unit.

2. Can these units be remotely mounted?

Only the RMR-8RDS and RMR-RS202 are remote installation units all the other units were not designed for remote mounting.

3. Which direction do the units face?

On both the scrambler and the combination units, the smoke screen and the green power light faces towards the inside of your vehicle, and the unit must be mounted level.

4. Can these units be hard-wired?

A: Yes:
1) Clip off the cigarette lighter end and connect the red wire to 12 volts and the other (white) wire to ground. Add an in-line wire fuse to the power side (red wire). The fuses should be a 5 amp/fast burning type.
2) The power cord with the solid white stripe. Connect the white stripe (ribbed) wire to 12 volts and the other (black) wire to ground. Add an in-line wire fuse to the power side (black-white wire). The fuses should be a 2 amp/fast burning type.
3) The power cord with the dotted white stripe. Connect the black wire to 12 volts, and the dotted white stripe wire to ground. Add an in-line wire fuse to the power side (black wire). The fuses should be a 2 amp/fast acting type.

5. Do any of RMR/KAT products come with a visor mount? Or can they be purchased seperate?

We do NOT have visor mounts to purchase seperate. The ONLY products that do come with valco for dash mounting is the KAT products

PRICING

1. Why are some Internet sites selling your products at a lower price?

Rocky Mountain Radar has noticed that several Internet sites are selling our product at a lower price, than most of our dealers. Not all of these are authorized dealers of Rocky Mountain Radar product. We advise you to think before buying from these dealers because we do not know if those units are not original product as represented, used or pirated.

GENERAL

1. Why are there so many websites that say Rocky Mountain Radar products do not work?

Rocky Mountain Radar is the Undisputed Technology Leader in the Radar Industry. We have the best pricing, the lowest return rate, no false alerts with our Smart-Scan, and the best warranty service. Other companies have had to resort to negative press to place doubts in our products. By hiring the likes of Craig Peterson, Tom Martino, "Radar" Roy and Carl Fors, (Fun by Fors and Speed Measurement Labs) these companies have maligned our product so they can look good.

2. I placed an order on the Rocky Mountain Radar site, my credit card statement says Radar Solutions Ltd. What's up?

Radar Solutions Ltd. has purchased all the assets of Rocky Mountain Radar including its name and trademarks. The web site will not be different but all billing and shipping info will show Radar Solutions Ltd. name.

TICKET REBATE PROGRAM

1. Can I register for the ticket rebate program on line?

No, the registration card must be filled out and signed, then returned. Keep the "How to file a claim form" in a safe spot. This will need to be completed and sent in with all ticket claims.

2. Can more than one person be registered for the ticket program?

Yes, it will be $19.95 to add a second person under the same registration number.

3. Can the ticket rebate be extended for another year?

Yes, you must send in $25.00 before the one year year expires. It would be $25.00 per person. It is only for 1 year. To extend it would $25.00 per year.

4. What if I have I lost my "How to file a claim" form?

You must send in proof of purchase to proces the ticket if you have lost the form.

5. What state can RMR not pay the ticket fines?

California and Tennessee

6. What do I need to file a ticket claim?

You must send in:
1) clear copy of ticket (no tracing)
2) proof of paying ticket
3) court address
4) claim form or proof of purchase

7. What is the registration card for?

The registration card enrolls you in our 1 year ticket rebate program. If you ever happen to receive a laser or radar ticket (based on what unit you have) within the one year we will have you on file. You can not register on line. IT MUST BE MAILED AND SIGNED.

The DLS/KAT/LJR and LSTK models cover only laser tickets.

Most Frquently Asked Questions on the "KAT PRODUCTS"

1. What is the MATRIX?

World’s only cordless performance meter with a three-axis accelerometer chip that measures the performance of your vehicle.

0-1/4 mile time and speed
0-60 MPH time
Peak HP and Average HP
Multi-run memory
1 inch back-lit display with large ½ inch data
Simple one-button operation
Programmable enhanced performance setup

2. What is the TRAXX?

The TRAXX is a full featured radar/laser detector with a laser scrambler plus the MATRIX performance meter circuitry.

3. Will the units scramble the roadside trailer signs that display your speed as you approach them?

No, the roadside trailer signs use radar to determine your speed not laser. Citations can’t be issued from these signs.

4. Is there a punch-through zone with the KAT600 or Traxx?

No, there is no punch-through with laser.

5. How do I know the scrambler is working?

The Kat 600 has a "L" light that will remain on while the scrambler is activated as long as the light is on the laser scrambler is working properly.

6. Which lights indicate what is operating on the KAT500?

On the KAT500 units, left to right:

1) Power – Amber
2) X – Red
3) K/KA –Green
4) City–Amber
5) VG2– Green
6) 2,3,4 signal strenght LEDS - red
7) For laser everything across will light up

7. Which lights indicate what is operating on the KAT600?

On the KAT600 units, left to right:
1) Power – Amber
2) X – Red
3) K/ ka – Green
4)City– Amber
5)Laser– Green
6) For laser everything across will light up
7)VG2 Alarm–"2,3,4" LEDs signal strengh–Red

8. How do I activate the VG-2 alert on the KAT500?

To disengage press and hold the City button down for an extended period of time (approx 3 to 5 seconds). The Kat500 will disengage VG-2 feature with Flat buzz sound. To Engage press and hold the City button down for an extended period of time (approx 3 to 5 seconds). The Kat500 will engage VG-2 feature with three beeps.

9. How do I activate the VG-2 alert on the KAT600?

Press and hold the City button until you hear 3 quick beeps. To deactivate, follow the same procedures but this time you will hear a flat buzz sound.

10. Do the units scramble 360°?

No, a scrambler is a forward scrambler only. The units detect 360°.

11. Does the KAT600 come with the scrambler activated?

Yes

12. How do you know the scrambler is activated on the KAT600?

On the KAT600, when you turn the unit on and it goes through the test mode you will see a “L” LED and you will hear a soft chirp from the speaker.

13. How does the performance meter work in the Traxx?

The TRAXX measures the performance of your vehicle by sensing acceleration forces. It uses a three-axis accelerometer to measure acceleration. This digital three-axis accelerometer sensor tracks your vehicle’s acceleration and cornering forces. This device analyzes data and calculates corrected G-Forces for the G Meter operation, speed and distance data. The result is the most accurate.

The TRAXX provides distinct visual and voice alerts to warn you of the presence of X, K and all kinds of Ka band radar guns in the front and rear of you. This model also provides the benefit of ‘undetectability’ by alerting you to the presence of VG-2 (Radar detector-detector). The unit also scrambles all laser devices.

The TRAXX has Safety alarm mode for safe driving. You can set safety level of lateral G-force. TRAXX gives warning sound and visual blinking whenever you exceed your level setting.

14. What can the Traxx/Matrix measure?

TRAXX/MATRIX can measure the followings:
1. Time to go from 0 to 60MPH (0 to 100Km)
2. Speed at the end of 1/4 mile (400m)
3. G-Force
4. Peak and Average Horsepower

15. What bands does the Traxx detect?

1. X, K and Superwide Ka band radar guns
2. Laser guns (Laser speed monitoring devices)
3. VG-2 undetectability

16. What do I do to set up the Traxx/Matrix for the 1st time?

If this is the first time the device is powered since installation or if the orientation has changed, please move the vehicle to a level place and calibrate the three-axis accelerometer.

(On the Kat-Traxx press Mode button to go G-FORCE mode and complete calibration by pressing START button.)

Both Units Kat Traxx/Matrix:
To accurately measure horsepower, the correct vehicle weight and the correction factor for the vehicle must also be entered to allow a horsepower calculation. To enter set-up mode, press MEMORY button for three (3) seconds at any mode of GFORCE / 0 TO 60/ 1/4mile except Radar Detector mode until default weight of 2000lbs shows in the display. Please enter
your vehicle weight and each correction factors.

17. How do I set up for metric use on the Traxx?

You can set up your TRAXX for US or Metric unit and calculate engine power in HP or PS (metric horsepower). When pressing ‘DOWN’ button and turn on the Power at the same time, it displays current engaged mode. Press UP/DOWN button to toggle ‘US’ or ‘METRIC’ and press ‘MEMORY’ button to select.
The factory default is ‘US’. Please enter its metric calculation factor. When ‘US’ or ‘METRIC’ is changed each other, its measurement will be changed as follows.
- US: Time to go from 0 to 60MPH / METRIC: 0 to 100Km
- US: Speed at the end of 1/4 mile / METRIC: 400m

18. How do I set up the Traxx/Matrix for my vehicle weight?

You must enter the weight of your vehicle. This information is available in your vehicle’s manual. You should add the weight of the driver, passengers and cargo plus any additional equipment added to the vehicle. Press the UP or DOWN button until the correct weight is shown. Holding either button for 1 second causes the weight to change rapidly. Press Start button to store the setting.

19. How do I set up my Traxx/Matric for Horsepower?

This is a correction factor you can set for an approximate
conversion from wheel horsepower to engine horsepower. Factory default is 1.00. The TRAXX/MATRIX is affected by drive train losses, rolling resistance and aerodynamic drag which determine the vehicle’s performance. Manufacturers’ ratings list a higher engine horsepower which is not reduced by these other real-world factor so you may need to increase the wheel horsepower readings to approximately correlate to higher engine horsepower. After storing vehicle weight, it automatically goes to Horsepower Factor. Display flashes previously set value. Press the UP and DOWN buttons until the vehicle correction shows in the display. Press Start button to store the setting.

20. How do I set up my Matrix for Horsepower Speed Range?

To accurately measure horsepower, the correct vehicle weight and correction factor must be entered.
To enter weight , press Memory button until Setup shows in the display. Then use the up/down buttons to enter correct weight (include driver and passengers). Press Store button to store setting. Next Setting will be the correction factor use the up/down button to enter the correction factor. Press Store to store the setting. To Set the minimum speed for the average horsepower use the up or down buttons. Press Store to store result. Ste the maximum speed for the average horsepower by pressing the up/down buttons. Press Store button to store results.

21. How does the performance meter work in the Matrix?

The Matrix measures the performance of your vehicle by sensing acceleration forces. It uses a three-axis accelerometer to measure acceleration. This digital three-axis accelerometer sensor tracks your vehicle’s acceleration and cornering forces. The result is the most accurate.
The Matrix will also display the number of horizontal and forward Gs. The right indicator is sideways acceleration with arrow that indicates direction. The left indicator is forward acceleration. The arrow pointing up is when speed is increasing and down when speed is decreasing.

22. Does the Traxx scramble Radar and Laser?

NO, it only scrambles laser. It will detect radar and laser.

23. What is a performance meter?

A: Matrix is a device that measures the performance of a vehicle by sensing acceleration forces. It uses a three-axis accelerometer to measure acceleration. This digital three-axis accelerometer sensor tracks your vehicle’s acceleration and cornering forces. This device analyzes data and calculates corrected G-forces for the G meter operation, speed and distance data.

24. What are the benefits of having a performance meter?

A: It is designed to enhance your driving experience. The performance meter will allow the driver to understand the vehicles capabilities.

25. What is G-Force?

A: G-Force is the force of gravity or acceleration on a body.

26. What can the Matrix measure?

A: It will measure peak and average horsepower, acceleration, G-force, time to go from 0 to 60mph and speed at the end of ¼ mile.

27. How long do the batteries last?

A: Battery life is approximately one year under normal daily use.

WARRANTY

1. What is the warranty on the C (combo) ,D, DLS, remote and KAT models?

The "C" model have a 3 year manufacture warranty. All other models have a 1year manufacture warranty.

2. How do I send in my unit for repair?

Send in:
1) unit
2) power cord
3) physical return address
4) telephone number
5) proof of purchase
6) short note stating the problem

You pay freight to us and we pay freight to you. It will be shipped back by UPS Ground.

Send To:
Rocky Mountain Radar
6469 Doniphan Dr.
El Paso, TX. 79932

3. What if I do not have proof of purchase?

If it is not the C475 or the Phazer 3, (because they came out in 2009) there will be an out of warranty fee.

A) All "C" combo units and the 8RDS - $62.00

B) All KAT, D, DLS, 8RD models - $25.00

C) PhazerII/Phazer3 - $37.00

4. How do I pay for the out of warranty fee?

We accept mc, visa, discover, money orders/cashier checks. If you send a personal check, we will hold your unit for 12 days.

5. What is the TAMPER FEE?

If the unit has been opened or tampered with there is a fee. See chart below:

1) "C" (combo) and 8RDS - $150.00
2) PhazerII/Phazer3 and 8RD - $75.00
3) KAT 500 & KAT 600 - $75.00
4) Matrix & Traxx - $75.00

RMR-8RDS/8RD/RS202/RS202D/LSTK/LJR REMOTE UNITS

1. What are Remote installation units?

A: Remote units are weatherproof external mount modules that are installed on the bumper or grill of the vehicles. Models come in various configurations for radar/laser detection and/or radar/laser scrambling.

2. Why won't my 8RD/8RDS unit turn on?

A: Check the following:
1) The on/off thumbwheel on the side of the unit
2) The fuse in the power cord. (To check the fuse in the power cord, unscrew the silver tip end that plugs into the cigarette lighter. If the fuse is blown, replace with a 2 amp fast burning fuse).
3) The fuse for your cigarette lighter
4) If it is none of these, return the unit to the manufacturer for repair/replace.

3. What is the Control Panel on the 8RD/8RDS units?

The Control Panel is the module that mounts inside the vehicle and reports what the front and rear antrnnas detect.

4. What if I have only the RD202/RS202D/LSTK/LJR Scramblers and want to use it with my own window mount radar detector?

They all can be used without connecting to the control panel. Cut and remeove the connector on the cable on the RD202/RS202D/LSTK/LJR. Stripthe wires back and connect the red wire to +12V and the white wire to ground. It is recommended that you connect to a switched +12V source on the fuse block inside the engine compartment.

5. Were is the best place to mount the RD202/RS202D/LSTK/LJR?

The idea location on the front of the vehicle is as close as possible to the front license plate area. Either on the grill or bumber. For the rear the ideal locaion is anywhere on the bumber close to the raer license plate. The officer usually targets your license plate area, especially with laser.

6. Were is the best place to mount the Control Panel?

The Control Panel does not need to view the road. It can be put in sight or out of sight for you. It has a digital display and voice alerts. It is recommended to be installed in a convenient location for the driver. Like the center console, instrument panel, steering column. It can even be installed in the dash or on the dash.

7. It the RS202/RS202D/LSTK/LJR"s waterproof?

The external modules are weatherproof not waterproof. Your vehicle is not waterproof it is weatherproof. Waterproof designates having the capability of being submerged in water to a specified depth. The external modules will handle any weather condition that your vehicle can.

8. Does the RS202/RS202D/LSTK/LJR"s need to have a clear view of the road?

Yes, install the RS202/RS202D/LSTK/LJR units in a manner where the lens has a clear view of the road without any obstructions.

9. Does the RMR-8RDS/8RD/RS202/RS202D/LSTK/LJR REMOTE UNITS come with all materials required for installing?

Yes, everything needed to install the units are included in the box. You may use additional hardware to customize your installation.

10. How hard is it to install the 8RDS/8RD/RS202/RS202D/LSTK/LJR REMOTE UNITS?

Each external module has one 16' cable attached that you route through the firewall to the power source.

11. How do I care for the RMR-8RDS/8RD/RS202/RS202D/LSTK/LJR REMOTE UNITS?

Keep the lens free and clear of debris, snow, mud and road crime.